Boise and the Treasure Valley

Metal Roof Replacement in Boise, ID

Full tear-off metal roof replacement for Boise and Treasure Valley homes — standing seam or exposed-fastener, matched to your budget and roof design, with a written per-square price before any work starts.

Typical range: $700–$1,800 per roofing square installed

Call (208) 279-6903

Metal Roof Replacement underway on a property in Boise, ID

Floating-clip standing seam — no screwed-through panels

Galvalume or better, matched to the manufacturer spec

Permit pulled on every job

Written per-square metal pricing

Old roofing hauled away

Last updated: 2026-08-23

Metal Roofing Boise is a roofing company serving Boise and the Treasure Valley, and metal roof replacement is one of the services we handle most. This page covers what the work involves here specifically — the climate, the code, and what it costs — rather than what it involves in general.

What we do on the first visit

The first visit is an inspection, not a sales call. We walk the roof with you, check the deck from the attic side where we can, count valleys and penetrations, and note the pitch and how much staging or safety equipment the job needs. We confirm whether any prior layers are on the roof already — code allows a maximum of two before a full tear-off is required — and then you get a written per-square price with tear-off and any deck repair as separate lines.

If we think repair is the better spend than replacement, or a different material suits your situation better, we say so on that visit — including when it means the smaller job for us.

What's included

On-site inspection and a written per-square price before any work starts, broken out by panel system
Full tear-off to the deck when code requires it — never a metal roof-over on a deck that can't take it
Deck inspection and replacement of any rotten or delaminated sheathing, priced as its own line
High-temperature synthetic underlayment across the field, ice-and-water membrane at eaves and valleys
New flashing, drip edge, and closures at every penetration, chimney, and wall tie-in — not reused off the old roof
Panel gauge, finish, and fastening system matched to the manufacturer's engineering spec for this climate
Snow guards placed over entries, walkways, and lower roofs where sheet-slide is a real risk
Full site cleanup with a magnet sweep for dropped fasteners and haul-away of the old roofing

What this costs in Boise

Metal Roof Replacement runs $700–$1,800 per roofing square installed in this area. 2026 published Boise-area installed pricing across both exposed-fastener and standing seam metal systems (HomeGuide, Angi 2026 national data cross-checked against mysignatureroofing.com's Boise-specific quote). The things that move a job up its range are tear-off, how much deck repair is needed, pitch, and how many valleys and penetrations your roof has. If you want a number before you call, the roof cost calculator will get you close.

When it needs doing

Panel seams separating or fasteners visibly backing out
Rust bleeding at cut edges, fastener heads, or valleys
Oil-canning (visible waviness) worsening across a panel run
Leaks at penetrations, chimneys, or wall flashings
Roof is a lower-grade galvanized system installed 20+ years ago and due for a proper upgrade
Considering a switch from shingle to metal for the longer service life

DIY metal panels, the cheapest bid, or the job done properly

	DIY weekend	Cheapest bid	Done properly
Panel fastening	Exposed screws driven by hand, spacing eyeballed	Exposed-fastener panels, minimum screw count to hit budget	Floating-clip standing seam or properly spaced exposed-fastener, matched to Boise’s thermal swing
Panel grade	Bargain galvanized off the shelf, no finish warranty	Standard galvanized, coating warranty rarely disclosed	Galvalume or better with a real paint-system warranty, disclosed in writing
Underlayment	Whatever’s left over, felt paper reused	Minimum-code synthetic underlayment	High-temp synthetic rated for the deck’s full range, ice-and-water membrane at valleys
Snow retention	Not considered	Skipped unless asked	Snow guards placed over entries, walkways, and lower roofs where sheet-slide is a real risk
Permit	Often skipped	Sometimes skipped	Pulled and inspected every time
If it fails	Your weekend, again, now with sharp trimmed edges	Chasing a phone number that stopped working	We come back and fix it

How it works

How metal roof replacement runs

01
Free on-site inspection
We walk the roof, check the deck from the attic side where we can, count penetrations and valleys, and hand you a written per-square price broken out by panel system — no pressure, no charge.
02
Permit and panel order
We pull the reroofing permit and order the exact panel system, gauge, and finish your roof needs — not a rounded-up estimate.
03
Tear-off and install
Deck repaired where needed, underlayment and flashing installed to spec, then panels installed with the fastening method — floating clip or through-fastened — engineered for this climate's thermal swing.
04
Inspection and walkthrough
Final inspection, magnet sweep for fasteners, gutters and landscaping checked for debris, and we walk the finished roof with you before we leave.

Get a free metal roof replacement estimate

A real person answers. We walk the roof with you, check the deck, and give you a written per-square price — at no charge and with no pressure.

Call (208) 279-6903

Questions

Metal Roof Replacement questions

How long does a metal roof replacement take in Boise?

Most single-family homes take two to four days once material is on-site, weather permitting — longer than shingle because panels are cut and fitted to the specific roof rather than laid from a bundle. Steep-pitch or heavily-cut roofs run longer. We give you a specific day estimate at the inspection.

Should I choose standing seam or exposed-fastener?

It depends on budget and how long you want to own the problem. Standing seam's floating-clip system handles Boise's thermal swing without loosening and typically runs 40-70 years with minimal maintenance. Exposed-fastener costs less up front but the screws need periodic re-tightening or replacement as the neoprene washers age — see our standing seam vs. exposed-fastener guide for the full comparison.

Can you install metal over my existing shingles?

Sometimes, if the deck and existing layer count support it — see our metal-over-shingles page for what qualifies. Many jobs are still full tear-offs, especially where the deck needs inspection or repair anyway.

Do you handle the permit?

Yes. Every city in this valley requires a reroofing permit even for a like-for-like metal reroof, and we pull it as part of the job.

Do you charge for an estimate?

No. Estimates are free across Boise and the Treasure Valley, including the drive. We walk the roof with you, check the deck from the attic side where we can, and hand you a written per-square price with tear-off and any deck repair broken out as their own lines.

Also worth a look

Related services

Standing Seam Metal Roofing

Concealed-fastener standing seam roofing with a floating-clip system engineered for Boise's wide temperature swing — steel or aluminum, snap-lock or mechanical seam, with a written per-square price before any work starts.

Exposed-Fastener Metal Roofing

Corrugated, R-panel, and 5V-crimp exposed-fastener metal roofing — the budget-conscious metal option, installed with the fastener spacing and sealing this climate actually needs, with a written per-square price before any work starts.

Metal Roof Repair

Targeted metal roof repair for leaks, backed-out fasteners, damaged panels, and seam separation — diagnosed correctly before anything is fixed, with a written price before any work starts.